- Article number:
- DK 7856.005
- Design
- With 3 m connection cable (connector type CEE/EN 60 309)
- Product description
- The modular system facilitates basic configuration of the racks, thanks to a vertical support rail with single-/3-phase infeed. The various socket modules to supply the active components may be snap-fitted into the support rail. This can even be done whilst the system is operational, because the support section is shock hazard-protected.
- Benefits
- Modules may be retrofitted whilst operational.
- Technical specifications
- Each plug-in module picks off a phase on the support rail, either from infeed or from the redundant infeed, depending on the direction of connection.
- Depending on the design, single-/3-phase construction with a maximum current of 2 x (3 x 16 A/32 A).
- 3-phase redundant infeed supported.
- The redundant circuit is completely separate from the 3 phases of the support rail.
- Modules may be equipped with integral overcurrent protection, so that only the affected module is deactivated in the event of an excessively high current. The other modules remain operational.
- Material
- Aluminium section, natural anodised
- Length of connection cable
- 3 m
- Type of electrical connection
- CEE
- Qty.
- 1
- Phases per infeed
- 3~
- Rated current (max.)
- 16 A
- Module slots (max.)
- 7
- To fit
- Enclosure type: TS 8
TS IT
VX IT
Height: 2,000 mm - Operating temperature range
- 5 °C...45 °C
- Ambient humidity (non-condensing)
- 5...95 %
- Storage temperature range
- -20 °C...60 °C
- Packs of
- 1 pc(s).
- Weight/pack
- 5.1 kg
- Customs tariff number
- 85369001
- EAN
- 4028177579200
- ETIM 7.0
- EC000215
- ECLASS 8.0
- 27371306
- Product description
- DK PSM busbar, 7-way, 3~, 16 A, Infeed: 1, For H: 2000 mm
Power System Module busbar with fixed infeed 3x16 A
The modular system allows basic equipment of each rack
with a vertical busbar and three-phase infeed.
The slots may be used over the entire enclosure
height due to the vertical arrangement.
Up to 7 socket modules may be snapped into the
slots and thanks to the shock-hazard-protected design
of the busbar it is not necessary to equip all slots
with socket modules.
Socket modules are available in various country
versions, e.g. IEC 320 C13, earthing pin, F/B, CH,
USA, UK. All modules may be mixed in the busbar. 7
socket modules may be inserted per 2 m of bar. Up to
42 C13 slots are available with IEC 320 modules.
Installation via the plug & play system:
The busbar may be installed in the FlexRack(i) without
adaptor or may be retrofitted in all Rittal TS/ PS
racks by means of the mounting kit DK 7856.011. Power
is supplied via a 5-core, 3 m long cable with open end
and wire end ferrules. The socket modules may be
replaced and retrofitted whilst operational.
Technical equipment:
Three-phase construction with max. 3x16 A. Socket
modules may be retrofitted whilst the system is
operational. Each module optionally with / without
integral miniature circuit-breaker.
Technical specifications:
Voltage range three-phase 110 V - 400 V AC 50/60 Hz
Neutral connector is required
Max. power supply 3x16 A
Temperature application range: +5° to +45°
Humidity application range: 5% to 95%
rel. humidity, non-condensing
Protection category IP20
H-section made of aluminium
W x H x D [mm]: 60 x 1908 x 60
Make/model: Rittal type: Busbar Power System Module
with fixed infeed DK 7856.005 or equivalent
The modular system allows basic equipment of each rack
with a vertical busbar and three-phase infeed.
The slots may be used over the entire enclosure
height due to the vertical arrangement.
Up to 7 socket modules may be snapped into the
slots and thanks to the shock-hazard-protected design
of the busbar it is not necessary to equip all slots
with socket modules.
Socket modules are available in various country
versions, e.g. IEC 320 C13, earthing pin, F/B, CH,
USA, UK. All modules may be mixed in the busbar. 7
socket modules may be inserted per 2 m of bar. Up to
42 C13 slots are available with IEC 320 modules.
Installation via the plug & play system:
The busbar may be installed in the FlexRack(i) without
adaptor or may be retrofitted in all Rittal TS/ PS
racks by means of the mounting kit DK 7856.011. Power
is supplied via a 5-core, 3 m long cable with open end
and wire end ferrules. The socket modules may be
replaced and retrofitted whilst operational.
Technical equipment:
Three-phase construction with max. 3x16 A. Socket
modules may be retrofitted whilst the system is
operational. Each module optionally with / without
integral miniature circuit-breaker.
Technical specifications:
Voltage range three-phase 110 V - 400 V AC 50/60 Hz
Neutral connector is required
Max. power supply 3x16 A
Temperature application range: +5° to +45°
Humidity application range: 5% to 95%
rel. humidity, non-condensing
Protection category IP20
H-section made of aluminium
W x H x D [mm]: 60 x 1908 x 60
Make/model: Rittal type: Busbar Power System Module
with fixed infeed DK 7856.005 or equivalent